Moderator Control Panel ]

How to upgrade the firmware for your Geekbox[Linux]

How-to guides on Geekbox.

Re: How to upgrade the firmware for your Geekbox[Linux]

Postby aegiap » Sat Jan 23, 2016 8:01 am

GeekBox wrote:
aegiap wrote:I have configured the usb-serial and using the c-kermit tool I can get a shell on the geekbox running the default ROM on ubuntu. Now I want to flash the lubuntu only ROM before starting to build my one basesystem based on Debian jessie.

The ugrade_tool still give me an error and cannot find the rockusb device. My regular as write access to the ttyUSB device and I tried as root to be sure but I get the same error.

I think I am missing something quite obvious but I don't get it.


Hi, aegiap:
c-kermit is just for usb-serial.
you need configure the mico-USB of Geekbox first.


Hello,

Ok, so the usb serial cable to the geekbox main board is only use for serial debugging.

I see the flash tool is an x86 binary:

Code: Select all
$ file ./upgrade_tool
./upgrade_tool: ELF 32-bit LSB executable, Intel 80386


If I connect a micro-USB / USB cable from the micro-USB port of the main geekbox board to my computer, I still do not have anything listed in lsusb. The flash tools does not find any device to flash:

Code: Select all
$ ./upgrade_tool
List of rockusb connected
No found rockusb,Rescan press <R>,Quit press <Q>:


I try starting the board while pressing the Update button on the board but the u-boot is still booting to the Linux kernel and the local lubuntu setup.

Edit: Success ! The flashing of a new firmware is currently running.
* connect a micro-USB cable to the micro-USB port of the geekbox mainboard,
* plug the power cable and the board will start
* then press the Update button as well as the Reboot button
* the board will be detected as an USB device by the flash tool,
* start the flash command : ./upgrade_tool uf update.img
aegiap
 
Posts: 9
Joined: Mon Dec 28, 2015 10:06 pm

Re: How to upgrade the firmware for your Geekbox[Linux]

Postby jim » Fri Nov 25, 2016 6:07 am

U-Boot 2014.10-RK3368-10-g8fe3a66 (Nov 24 2016 - 17:42:17)

CPU: rk3368
CPU's clock information:
arm pll big = 816000000HZ
arm pll little = 600000000HZ
periph pll = 576000000HZ
ddr pll = 1200000000HZ
codec pll = 400000000HZ
Board: Rockchip platform Board
Uboot as second level loader
DRAM: Found dram banks: 1
Adding bank:0000000000200000(000000007fe00000)
128 MiB
storage init OK!
Using default environment

GetParam
check parameter success
remotectl v0.1
failed to prepare fdt from boot!
power key: bank-0 pin-2
can't find dts node for ricoh619
can't find dts node for act8846
dwc_otg_check_dpdm: usb bc disconnected
pmic:rk808
can't find dts node for pwm0
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2016-11-15#2.54
empty serial no.
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
read logo on state from dts [1]
can't find dts node for deviceinfo
rk_hdmi_register:fail to read deviceinfo
hdmi baseparamer 0x0@0-0
tve baseparamer 1309360x0@20357318-157878
[EDID-EXTEND] It is a CEA 861 Series Extension.
no baseparametr,find best edid mode,vic=16
hdmi_dev->video.vic is 16
hdmi_dev_config_video vic 16 color_output 3 color_output_depth 8
pixel clk is 148500000 tmds clk is 148500000
hsync_pol 1 vsync_pol 1
[HDMI] sucess output HDMI.
failed to find part:logo
no fuel gauge found
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
got recovery cmd from misc.
load fdt from resouce.
ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
Secure Boot state: 0
kernel @ 0x00280000 (0x00ccd740)
ramdisk @ 0x05bf0000 (0x002ad558)
bootrk: do_bootm_linux...
Loading Device Tree to 0000000005600000, end 0000000005619d59 ... OK
Add bank:0000000000200000, 000000007fe00000

Starting kernel ...

[ 0.000000] [0: swapper: 0] Initializing cgroup subsys cpu
[ 0.000000] [0: swapper: 0] Initializing cgroup subsys cpuacct
[ 0.000000] [0: swapper: 0] Linux version 3.10.0 (jim@jim-desktop) (gcc version 4.9 20140514 (prerelease) (GCC) ) #2 SMP PREEMPT Thu Nov 6
[ 0.000000] [0: swapper: 0] CPU: AArch64 Processor [410fd033] revision 3
[ 0.000000] [0: swapper: 0] Machine: rockchip,rk3368
[ 0.000000] [0: swapper: 0] rockchip_uboot_logo_setup: mem: 0x0000000002000000@0x000000007dc00000, offset:0x0000000000000000
[ 0.000000] [0: swapper: 0] hdmi init vic is 16
[ 0.000000] [0: swapper: 0] rockchip_uboot_mem_reserve: reserve 0x0000000002000000@0x000000007dc00000 for uboot logo
[ 0.000000] [0: swapper: 0] rockchip_ion_reserve
[ 0.000000] [0: swapper: 0] ion heap(cma): base(0) size(0) align(0)
[ 0.000000] [0: swapper: 0] ion heap(vmalloc): base(0) size(0) align(0)
[ 0.000000] [0: swapper: 0] cma: CMA: reserved 16 MiB at 7cc00000
[ 0.000000] [0: swapper: 0] psci: probing for conduit method from DT.
[ 0.000000] [0: swapper: 0] psci: PSCIv1.0 detected in firmware.
[ 0.000000] [0: swapper: 0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] [0: swapper: 0] PERCPU: Embedded 11 pages/cpu @ffffffc07fd16000 s13440 r8192 d23424 u45056
[ 0.000000] [0: swapper: 0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 516615
[ 0.000000] [0: swapper: 0] Kernel command line: earlyprintk=uart8250-32bit,0xff690000 console=ttyS2 androidboot.baseband=N/A androidboot1
[ 0.000000] [0: swapper: 0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] [0: swapper: 0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] [0: swapper: 0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] [0: swapper: 0] Memory: 2046MB = 2046MB total
[ 0.000000] [0: swapper: 0] Memory: 1996220k/1996220k available, 98884k reserved
[ 0.000000] [0: swapper: 0] Virtual kernel memory layout:
[ 0.000000] [0: swapper: 0] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
[ 0.000000] [0: swapper: 0] vmemmap : 0xffffffbc00007000 - 0xffffffbc01c00000 ( 27 MB)
[ 0.000000] [0: swapper: 0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] [0: swapper: 0] memory : 0xffffffc000000000 - 0xffffffc07fe00000 ( 2046 MB)
[ 0.000000] [0: swapper: 0] .init : 0xffffffc000b79000 - 0xffffffc000bbc480 ( 270 kB)
[ 0.000000] [0: swapper: 0] .text : 0xffffffc000080000 - 0xffffffc000b787b4 ( 11234 kB)
[ 0.000000] [0: swapper: 0] .data : 0xffffffc000bbd000 - 0xffffffc000d4d740 ( 1602 kB)
[ 0.000000] [0: swapper: 0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] [0: swapper/0: 0] Preemptible hierarchical RCU implementation.
[ 0.000000] [0: swapper/0: 0] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] [0: swapper/0: 0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] [0: swapper/0: 0] Architected cp15 timer(s) running at 24.00MHz (virt).
[ 1.513098] [0: swapper/0: 0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 1.513132] [0: swapper/0: 0] pid_max: default: 32768 minimum: 301
[ 1.513335] [0: swapper/0: 0] Security Framework initialized
[ 1.513369] [0: swapper/0: 0] SELinux: Initializing.
[ 1.513528] [0: swapper/0: 0] Mount-cache hash table entries: 256
[ 1.514506] [0: swapper/0: 0] Initializing cgroup subsys debug
[ 1.514538] [0: swapper/0: 0] Initializing cgroup subsys freezer
[ 1.516523] [0: swapper/0: 1] /cpus/cpu@0: Missing clock-frequency property
[ 1.516587] [0: swapper/0: 1] /cpus/cpu@1: Missing clock-frequency property
[ 1.516649] [0: swapper/0: 1] /cpus/cpu@2: Missing clock-frequency property
[ 1.516712] [0: swapper/0: 1] /cpus/cpu@3: Missing clock-frequency property
[ 1.516777] [0: swapper/0: 1] /cpus/cpu@100: Missing clock-frequency property
[ 1.516844] [0: swapper/0: 1] /cpus/cpu@101: Missing clock-frequency property
[ 1.516916] [0: swapper/0: 1] /cpus/cpu@102: Missing clock-frequency property
[ 1.516990] [0: swapper/0: 1] /cpus/cpu@103: Missing clock-frequency property
[ 1.517021] [0: swapper/0: 1] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 1.518293] [0: swapper/0: 1] last_log: 0x000000007a480000 map to 0xffffff8000012000 and copy to 0xffffff8000094000, size 0x80000 early 0x1)
[ 1.591597] [1: swapper/1: 0] CPU1: Booted secondary processor
[ 1.611252] [2: swapper/2: 0] CPU2: Booted secondary processor
[ 1.630926] [3: swapper/3: 0] CPU3: Booted secondary processor
[ 1.650617] [4: swapper/4: 0] CPU4: Booted secondary processor
[ 1.670280] [5: swapper/5: 0] CPU5: Booted secondary processor
[ 1.689976] [6: swapper/6: 0] CPU6: Booted secondary processor
[ 1.709641] [7: swapper/7: 0] CPU7: Booted secondary processor
[ 1.709815] [0: swapper/0: 1] Brought up 8 CPUs
[ 1.709909] [0: swapper/0: 1] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[ 1.711155] [0: swapper/0: 1] devtmpfs: initialized
[ 1.718139] [0: swapper/0: 1] sched: registering cpufreq notifiers for scale-invariant loads
[ 1.718418] [0: swapper/0: 1] pinctrl core: initialized pinctrl subsystem
[ 1.718777] [0: swapper/0: 1] regulator-dummy: no parameters
[ 1.734388] [0: swapper/0: 1] NET: Registered protocol family 16
[ 1.735634] [0: swapper/0: 1] ion_snapshot: 0x7a718000 map to 0xffffff8000115000 and copy to 0xffffffc000e1e4a8 (version 0.1)
[ 1.736781] [0: swapper/0: 1] vdso: 2 pages (1 code, 1 data) at base ffffffc000bc5000
[ 1.736847] [0: swapper/0: 1] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 1.738524] [0: swapper/0: 1] software IO TLB [mem 0x7a000000-0x7a400000] (4MB) mapped at [ffffffc079e00000-ffffffc07a1fffff]
[ 1.740368] [0: swapper/0: 1] DMA: preallocated 256 KiB pool for atomic allocations
[ 1.741341] [0: swapper/0: 1] rk_clk_tree_init start!
[ 1.770292] [0: swapper/0: 1] rk_get_uboot_display_flag: uboot_logo_on = 1
[ 1.770384] [0: swapper/0: 1] rkclk_init_clks: cnt_parent = 8
[ 1.770807] [0: swapper/0: 1] rkclk_init_clks: cnt_rate = 30
[ 1.777354] [0: swapper/0: 1] syscon ff610000.syscon: regmap [mem 0xff610000-0xff6103ff] registered
[ 1.777554] [0: swapper/0: 1] syscon ff730000.syscon: regmap [mem 0xff730000-0xff730fff] registered
[ 1.777789] [0: swapper/0: 1] syscon ff738000.syscon: regmap [mem 0xff738000-0xff738fff] registered
[ 1.777987] [0: swapper/0: 1] syscon ff740000.syscon: regmap [mem 0xff740000-0xff740fff] registered
[ 1.778235] [0: swapper/0: 1] syscon ff760000.syscon: regmap [mem 0xff760000-0xff760fff] registered
[ 1.778443] [0: swapper/0: 1] syscon ff770000.syscon: regmap [mem 0xff770000-0xff770fff] registered
[ 1.778636] [0: swapper/0: 1] syscon ffac0000.syscon: regmap [mem 0xffac0000-0xffac2fff] registered
[ 1.784539] [0: swapper/0: 1] rk_iommu ff900800.iep_mmu: (iep) Enter
[ 1.784657] [0: swapper/0: 1] rk_iommu ff900800.iep_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 1.784685] [0: swapper/0: 1] rk_iommu ff900800.iep_mmu: (iep) Initialized
[ 1.784881] [0: swapper/0: 1] rk_iommu ff950800.vip_mmu: (vip) Enter
[ 1.784962] [0: swapper/0: 1] rk_iommu ff950800.vip_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 1.784990] [0: swapper/0: 1] rk_iommu ff950800.vip_mmu: (vip) Initialized
[ 1.785173] [0: swapper/0: 1] rk_iommu ff930300.vop_mmu: (vop) Enter
[ 1.785254] [0: swapper/0: 1] rk_iommu ff930300.vop_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 1.785282] [0: swapper/0: 1] rk_iommu ff930300.vop_mmu: (vop) Initialized
[ 1.785477] [0: swapper/0: 1] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
[ 1.785565] [0: swapper/0: 1] rk_iommu ff914000.isp_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 1.785593] [0: swapper/0: 1] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
[ 1.785920] [0: swapper/0: 1] rk_iommu ff9a0440.hevc_mmu: (hevc) Enter
[ 1.786003] [0: swapper/0: 1] rk_iommu ff9a0440.hevc_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 1.786031] [0: swapper/0: 1] rk_iommu ff9a0440.hevc_mmu: (hevc) Initialized
[ 1.786246] [0: swapper/0: 1] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
[ 1.786345] [0: swapper/0: 1] rk_iommu ff9a0800.vpu_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
[ 1.786373] [0: swapper/0: 1] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
[ 1.795970] [0: swapper/0: 1] rockchip_pinctrl_probe:init ok
[ 1.797627] [0: swapper/0: 1] process version: 0
[ 1.797712] [0: swapper/0: 1] channel:0, lkg:25
[ 1.797741] [0: swapper/0: 1] target-temp:80
[ 1.797788] [0: swapper/0: 1] channel:0, lkg:25
[ 1.797815] [0: swapper/0: 1] target-temp:80
[ 1.797901] [0: swapper/0: 1] channel:2, lkg:32
[ 1.797941] [0: swapper/0: 1] channel:1, lkg:0
[ 1.826687] [0: swapper/0: 1] bio: create slab <bio-0> at 0
[ 1.827367] [0: swapper/0: 1] Rockchip hdmi driver version 2.0
[ 1.827367] [0: swapper/0: 1] .
[ 1.828014] [0: swapper/0: 1] SCSI subsystem initialized
[ 1.828223] [0: swapper/0: 1] usbcore: registered new interface driver usbfs
[ 1.828288] [0: swapper/0: 1] usbcore: registered new interface driver hub
[ 1.828429] [0: swapper/0: 1] usbcore: registered new device driver usb
[ 1.830515] [0: swapper/0: 1] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
[ 1.830699] [0: swapper/0: 1] media: Linux media interface: v0.10
[ 1.830761] [0: swapper/0: 1] Linux video capture interface: v2.00
[ 1.830854] [0: swapper/0: 1] pps_core: LinuxPPS API ver. 1 registered
[ 1.830879] [0: swapper/0: 1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.830917] [0: swapper/0: 1] PTP clock support registered
[ 1.830994] [0: swapper/0: 1] i2c-core: driver [bq24296] using legacy suspend method
[ 1.831018] [0: swapper/0: 1] i2c-core: driver [bq24296] using legacy resume method
[ 1.831425] [0: swapper/0: 1] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203)
[ 1.832139] [0: swapper/0: 1] Rockchip ion module is successfully loaded (v1.1)
[ 1.832367] [0: swapper/0: 1] rockchip-mailbox ff6b0000.mbox: Rockchip mailbox initialize, version: V1.00
[ 1.833173] [0: swapper/0: 1] mbox-scpi mbox-scpi.7: Scpi initialize, version: 0x1000001, chan nums: 3
[ 1.833204] [0: swapper/0: 1] mbox-scpi mbox-scpi.7: MCU version: V2.12 20151111
[ 1.833587] [0: swapper/0: 1] Advanced Linux Sound Architecture Driver Initialized.
[ 1.834097] [0: swapper/0: 1] Bluetooth: Core ver 2.16
[ 1.834161] [0: swapper/0: 1] NET: Registered protocol family 31
[ 1.834186] [0: swapper/0: 1] Bluetooth: HCI device and connection manager initialized
[ 1.834217] [0: swapper/0: 1] Bluetooth: HCI socket layer initialized
[ 1.834245] [0: swapper/0: 1] Bluetooth: L2CAP socket layer initialized
[ 1.834289] [0: swapper/0: 1] Bluetooth: SCO socket layer initialized
[ 1.834603] [0: kworker/0:1: 51] cfg80211: Calling CRDA to update world regulatory domain
[ 1.836327] [0: swapper/0: 1] rk808_i2c_probe,line=1355
[ 1.836970] [0: swapper/0: 1] rk808_pre_init,line=1224
[ 1.854515] [0: swapper/0: 1] vdd_arm: 712 <--> 1500 mV at 1150 mV
[ 1.861599] [0: swapper/0: 1] vdd_logic: 712 <--> 1500 mV at 1200 mV
[ 1.868380] [0: swapper/0: 1] vcc_ddr: 1200 mV
[ 1.877488] [0: swapper/0: 1] vccio: 3300 mV
[ 1.884206] [0: swapper/0: 1] vcc_flash: 1800 mV
[ 1.890933] [0: swapper/0: 1] vcca_33: 3300 mV
[ 1.897633] [0: swapper/0: 1] vdd_10: 1000 mV
[ 1.904371] [0: swapper/0: 1] vcca_18: 1800 mV
[ 1.909010] [0: swapper/0: 1] vccio_sd: 1800 <--> 3300 mV at 3300 mV
[ 1.915718] [0: swapper/0: 1] vdd10_lcd: 1100 mV
[ 1.922434] [0: swapper/0: 1] vcc_18: 1800 mV
[ 1.929135] [0: swapper/0: 1] vccio18_lcd: 1800 mV
[ 1.933772] [0: swapper/0: 1] vcc_sd: 1800 <--> 3300 mV at 3300 mV
[ 1.940496] [0: swapper/0: 1] vcc_lan: 3300 mV
[ 1.943411] [0: swapper/0: 1] rk808_irq_init: rk808_pmic_irq=0
[ 1.944025] [0: swapper/0: 1] rk808_rtc_probe,line=540
[ 1.961586] [0: swapper/0: 1] rk808-rtc rk808-rtc: rtc core: registered rk808 as rtc0
[ 1.965266] [0: swapper/0: 1] rk808_rtc_probe:ok
[ 1.966479] [0: swapper/0: 1] This platfrom have not i2s_mclk,no need to set i2s_mclk.
[ 1.967509] [0: swapper/0: 1] Switching to clocksource arch_sys_counter
[ 1.970387] [0: swapper/0: 1] rga: Module initialized.
[ 1.970843] [0: swapper/0: 1] rga2 ff920000.rga: rga ion client create success!
[ 1.971019] [0: swapper/0: 1] rga: Driver loaded succesfully
[ 1.971301] [0: swapper/0: 1] fb disp policy is box
[ 1.971374] [0: swapper/0: 1] rk-fb rockchip-fb: rk fb ion client create success!
[ 1.971402] [0: swapper/0: 1] rk-fb rockchip-fb: rockchip framebuffer driver probe
[ 1.971892] [0: swapper/0: 1] rk-screen rk_screen.12: rockchip screen probe success
[ 1.973158] [0: swapper/0: 1] rk3368-lcdc ff930000.lcdc: lcdc_dev->regs=0xffffff8000280000
[ 1.973577] [0: swapper/0: 1] graphics fb0: rockchip framebuffer registerd:fb0
[ 1.973978] [0: swapper/0: 1] graphics fb1: rockchip framebuffer registerd:fb1
[ 1.97418 registerd:fb2
[ 1.974388] [0: swapper/0: 1] graphics fb3: rockchip framebuffer registerd:fb3
[ 1.974595] [0: swapper/0: 1] graphics fb4: rockchip framebuffer registerd:fb4
[ 1.975365] [0: swapper/0: 1] rk3368-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
[ 1.988756] [0: swapper/0: 1] alloc_buffer:ion_phy_addr=0x10000000
[ 1.993227] [0: swapper/0: 1] fb0:phy:10000000>>vir:ffffff8000291000>>len:0x1000000
[ 2.093354] [0: swapper/0: 1] rk_iommu ff930300.vop_mmu: rockchip_iommu_attach_device: Attached new IOMMU with pgtable 0x7a7ce000
[ 2.093428] [0: swapper/0: 1] rk3368-lcdc lcdc0: lcdc0 probe ok, iommu enabled
[ 2.095510] [0: swapper/0: 1] NET: Registered protocol family 2
[ 2.096507] [0: swapper/0: 1] TCP established hash table entries: 16384 (order: 6, 262144 bytes)
[ 2.096988] [0: swapper/0: 1] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 2.097481] [0: swapper/0: 1] TCP: Hash tables configured (established 16384 bind 16384)
[ 2.097589] [0: swapper/0: 1] TCP: reno registered
[ 2.097621] [0: swapper/0: 1] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 2.097719] [0: swapper/0: 1] UDP-Lite hash table entrie



don't startup ...


GeekBox , can you help me?


there may be somethings about
jim
 
Posts: 1
Joined: Fri Nov 25, 2016 6:02 am

Кредиты малому, среднему бизнесу и частным лицам без обеспеч

Postby Juristfaupe » Wed May 10, 2017 4:57 pm

СКБ-Банк – один из крупнейших региональных российских банков, ровесник банковской системы современной России.

Банку присвоены высокие рейтинги агентств Fitch и Moody's. Сегодня СКБ-Банк – в пятерке крупнейших региональных банков России.

Условия получения кредита наличными в СКБ-Банк:

Сумма кредита - от 51 000 до 1 300 000 руб.

Срок кредитования - до 60 мес.

Процентная ставка - от 15,9%

Обеспечение - не требуется

-------------------------------------------------------------------------------------------------------

Требования к заемщикам:

Возраст - от 23 до 70 лет
Стаж работы на последнем месте работы - не менее 3 месяцев
Гражданство РФ
Регистрация и фактическое проживание на территории РФ

Заполнить заявку

Image
Juristfaupe
 
Posts: 16
Joined: Wed May 10, 2017 11:51 am
Location: Россия

Кредиты малому, среднему бизнесу и частным лицам без обеспеч

Postby Juristfaupe » Wed May 10, 2017 4:57 pm

СКБ-Банк – один из крупнейших региональных российских банков, ровесник банковской системы современной России.

Банку присвоены высокие рейтинги агентств Fitch и Moody's. Сегодня СКБ-Банк – в пятерке крупнейших региональных банков России.

Условия получения кредита наличными в СКБ-Банк:

Сумма кредита - от 51 000 до 1 300 000 руб.

Срок кредитования - до 60 мес.

Процентная ставка - от 15,9%

Обеспечение - не требуется

-------------------------------------------------------------------------------------------------------

Требования к заемщикам:

Возраст - от 23 до 70 лет
Стаж работы на последнем месте работы - не менее 3 месяцев
Гражданство РФ
Регистрация и фактическое проживание на территории РФ

Заполнить заявку

Image
Juristfaupe
 
Posts: 16
Joined: Wed May 10, 2017 11:51 am
Location: Россия

Previous

Return to Wiki

Who is online

Users browsing this forum: No registered users and 1 guest